高级检索

    云层阴影形状对光热发电吸热器光热耦合特性影响研究

    Influence of cloud shadow shapes on the solar to thermal characteristics of the receivers in solar power tower system

    • 摘要: 塔式太阳能光热发电作为一种可调度的清洁能源技术,在实际运行中常受到云层遮挡的影响,造成入射能流密度的不断变化,进而导致吸热器的能量产出不稳定及寿命衰减。目前研究大多是对定日镜场在均匀辐射衰减或规则形状云层下的热性能,真实云层对吸热器热性能及管道温度的影响研究较少。为了探究实际云层遮挡对定日镜聚光及吸热器传热性能的影响,以Crescent Dunes塔式光热电站为研究原型,建立了结合云图空间映射的定日镜场与吸热器光热耦合数值计算模型。将实际云层阴影图像进行分割转换,得到二值化图像,导入到SolarPILOT的Python API程序当中,获取云层阴影对吸热器聚光能流密度分布的影响规律,然后通过吸热器的光-热转换多物理场耦合分析模型,获取阴影对吸热器热性能及温度分布的影响。通过遮挡比例在20%至50%之间的多组真实云层形状数据进行模拟,分析了复杂阴影形状状态下吸热器表面的聚光能流密度分布、熔融盐流量、管壁温度以及薄膜温度等的变化。结果表明:吸热器表面的聚光能流分布不仅受到总体遮挡面积的影响,也与云层阴影的形状密切相关。云层阴影容易引起峰值能流密度位置偏移,造成能流密度多峰分布,在回路熔融盐质量流量偏低时可能造成熔融盐温度超过热分解限值,薄膜温度也会出现超过650℃运行界限的情况,造成吸热器管道腐蚀速率显著升高,给吸热器的安全运行带来风险。此外,当系统为维持工质出口温度而下调质量流量时,因局部热点区域的存在,吸热器表面的对流与辐射热损失未能随入射总能量的下降而成比例减少,导致吸热器的宏观热效率逐渐降至85%以下,且效率波动幅度有所增加。研究结果可为复杂云层条件下吸热器流量的协调分配及运行调节提供理论参考和技术支撑。

       

      Abstract: Solar power tower is a dispatchable clean energy technology, but its performance will be affected by cloud covers during actual operation, resulting in continuous changes in the concentrated solar energy, which in turn leads to unstable energy output and safety problem of the receiver. At present, most researches focused on the thermalperformance of the heliostat field under uniform radiation attenuation or regular cloud cover shapes. The influence of real cloud covers on the thermal performance of the receiver and tube temperatures was scarce. In order to investigate the influence of real cloud cover on the focusing and heat transfer performance of the heliostats and the receiver, a numerical calculation model was developed. The model coupled the heliostat field and the receiver under real cloud shadows. The Crescent Dunes tower plant was used as the research prototype. The image of real cloud shadow was segmented and converted into a binary image, which was imported into the Python API program of the SolarPILOT software. So, the influence cloud shadow on the concentrated heat flux distribution of the receiver could be obtained. Then, a multi-physics coupled model was developed to obtain the thermal performance and temperature distribution of the receiver. By using a multiple sets of real cloud shapes, which had a shadow ratio ranging from 20% to 50%, the changes in the concentrated heat flux distribution, the molten salt flow rate, the tube wall temperature, and the film temperature were analyzed. The results indicate that the distribution of concentrated heat flux on the receiver was not only affected by the overall shadowed areas, but also affected by the shape of cloud shadows. Cloud shadows could easily cause the location change of the peak heat flux, resulting in a multimodal distribution of the heat flux. When the mass flow rate of molten salt in the circuit was small, the molten salt temperature might be higher than its thermal decomposition limit, and the film temperature might also be higher than the operating limit of 650 ℃, which causing a significant increase in the corrosion rate of the tube. So, the safe operation the receive was affected. To maintain the outlet temperature of the working fluid, the plant should reduce the mass flow rate under cloudy conditions, and there existed hot spots on the receiver. So, the convective and radiative heat losses of the receiver did not decrease proportionally with the decrease of the total incident energy, resulting in the thermal efficiency of the receiver lower than 85%. And the efficiency would fluctuate for different cloud shapes. The present research can provide theoretical and technical support for the safe operation of receiver under cloudy conditions.

       

    /

    返回文章
    返回